You have no items in your shopping cart.
Our newest audio power amplifier is based on the Texas Instruments new TAS5630 digital amplifier chip, a high-performance, integrated stereo feedback, analog-input, digital amplifier with a power stage designed to drive 2-Ω to 8-Ω speakers at up to 300 W per channel in stereo, or up to 600W bridged. This amplifier requires only a single 20V to 50V power supply to deliver high-quality, high-efficiency audio amplification.
This amplifier is configured with two BTL channels or one PBTL channel and the possibility to apply either a standard single-ended or a balanced (differential) analog input signal. Since channels are BTL (bridge tied load) bus pumping is never an issue with these amplifiers.
The input section of the amplifier has two OPA1632 opamps... very high-performance, fully differential, audio operational amplifier designed to operate with single-ended or differential input signals (balanced). Output section features our custom made high performance inductors and metallized polypropylen capacitors. This is a very high quality power amplifier, and as always, made with the state-of-the-art materials and impeccable workmanship Class D Audio is known for.
Small Size - 5.25" X 3.75" (133.35mm X 95.25mm)
Click & Pop Noise Reduction
Short Circuit and Thermal Protection
Two Speed 12V Fan Output (most conditions will not require a fan)
Sync Input
Stereo or Bridged Configuration
House Keeping Power Supplies Built-In... only requires one 20V to 50V power Supply
Specification:
Output stage supply voltage 20 V – 50 V
Number of channels 2
Load impedance 2 to 8 Ω
Output power, 4 Ω, 310 W
Dynamic range >100 dB(A)
SE to differential amplifier OPA1632D
Output stage TAS5630
THD+N, 4 Ω: 1 W <0.05% 1 kHz
THD+N, 4 Ω: 10 W <0.04% 1 kHz
THD+N, 4 Ω: 50 W <0.02% 1 kHz
THD+N, 4 Ω: 100 W <0.03% 1 kHz
THD+N, 4 Ω: 200 W <0.40% 1 kHz
THD+N, 8 Ω: 1 W <0.04% 1 kHz
THD+N, 8 Ω: 10 W <0.03% 1 kHz
THD+N, 8 Ω: 50 W <0.02% 1 kHz
THD+N, 8 Ω: 100 W <0.10% 1 kHz
Dynamic Range: >100 dB Ref: rated power, A-weighted, AES17 filter, 2 ch avg
Noise Voltage: 320 μVrms A-weighted, AES17 filter
Click/Pop, DC step: <30 mV Mute/Unmute, No signal, 4 Ω
Channel Separation: >89 dB 1 kHz
Frequency Response: ±0.5 dB 100 W / 8 Ω, unclipped
This amplifier is configured with two BTL channels or one PBTL channel and the possibility to apply either a standard single-ended or a balanced (differential) analog input signal. Since channels are BTL (bridge tied load) bus pumping is never an issue with these amplifiers.
The input section of the amplifier has two OPA1632 opamps... very high-performance, fully differential, audio operational amplifier designed to operate with single-ended or differential input signals (balanced). Output section features our custom made high performance inductors and metallized polypropylen capacitors. This is a very high quality power amplifier, and as always, made with the state-of-the-art materials and impeccable workmanship Class D Audio is known for.
Small Size - 5.25" X 3.75" (133.35mm X 95.25mm)
Click & Pop Noise Reduction
Short Circuit and Thermal Protection
Two Speed 12V Fan Output (most conditions will not require a fan)
Sync Input
Stereo or Bridged Configuration
House Keeping Power Supplies Built-In... only requires one 20V to 50V power Supply
Specification:
Output stage supply voltage 20 V – 50 V
Number of channels 2
Load impedance 2 to 8 Ω
Output power, 4 Ω, 310 W
Dynamic range >100 dB(A)
SE to differential amplifier OPA1632D
Output stage TAS5630
THD+N, 4 Ω: 1 W <0.05% 1 kHz
THD+N, 4 Ω: 10 W <0.04% 1 kHz
THD+N, 4 Ω: 50 W <0.02% 1 kHz
THD+N, 4 Ω: 100 W <0.03% 1 kHz
THD+N, 4 Ω: 200 W <0.40% 1 kHz
THD+N, 8 Ω: 1 W <0.04% 1 kHz
THD+N, 8 Ω: 10 W <0.03% 1 kHz
THD+N, 8 Ω: 50 W <0.02% 1 kHz
THD+N, 8 Ω: 100 W <0.10% 1 kHz
Dynamic Range: >100 dB Ref: rated power, A-weighted, AES17 filter, 2 ch avg
Noise Voltage: 320 μVrms A-weighted, AES17 filter
Click/Pop, DC step: <30 mV Mute/Unmute, No signal, 4 Ω
Channel Separation: >89 dB 1 kHz
Frequency Response: ±0.5 dB 100 W / 8 Ω, unclipped
| Featured products | Yes |
| Description | Our newest audio power amplifier is based on the Texas Instruments new TAS5630 digital amplifier chip, a high-performance, integrated stereo feedback, analog-input, digital amplifier with a power stage designed to drive 2-Ω to 8-Ω speakers at up to 300 W per channel in stereo, or up to 600W bridged. This amplifier requires only a single 20V to 50V power supply to deliver high-quality, high-efficiency audio amplification. This amplifier is configured with two BTL channels or one PBTL channel and the possibility to apply either a standard single-ended or a balanced (differential) analog input signal. Since channels are BTL (bridge tied load) bus pumping is never an issue with these amplifiers. The input section of the amplifier has two OPA1632 opamps... very high-performance, fully differential, audio operational amplifier designed to operate with single-ended or differential input signals (balanced). Output section features our custom made high performance inductors and metallized polypropylen capacitors. This is a very high quality power amplifier, and as always, made with the state-of-the-art materials and impeccable workmanship Class D Audio is known for. Small Size - 5.25" X 3.75" (133.35mm X 95.25mm) Click & Pop Noise Reduction Short Circuit and Thermal Protection Two Speed 12V Fan Output (most conditions will not require a fan) Sync Input Stereo or Bridged Configuration House Keeping Power Supplies Built-In... only requires one 20V to 50V power Supply Specification: Output stage supply voltage 20 V – 50 V Number of channels 2 Load impedance 2 to 8 Ω Output power, 4 Ω, 310 W Dynamic range >100 dB(A) SE to differential amplifier OPA1632D Output stage TAS5630 THD+N, 4 Ω: 1 W <0.05% 1 kHz THD+N, 4 Ω: 10 W <0.04% 1 kHz THD+N, 4 Ω: 50 W <0.02% 1 kHz THD+N, 4 Ω: 100 W <0.03% 1 kHz THD+N, 4 Ω: 200 W <0.40% 1 kHz THD+N, 8 Ω: 1 W <0.04% 1 kHz THD+N, 8 Ω: 10 W <0.03% 1 kHz THD+N, 8 Ω: 50 W <0.02% 1 kHz THD+N, 8 Ω: 100 W <0.10% 1 kHz Dynamic Range: >100 dB Ref: rated power, A-weighted, AES17 filter, 2 ch avg Noise Voltage: 320 μVrms A-weighted, AES17 filter Click/Pop, DC step: <30 mV Mute/Unmute, No signal, 4 Ω Channel Separation: >89 dB 1 kHz Frequency Response: ±0.5 dB 100 W / 8 Ω, unclipped |
-
Amazing specs Review by raj
Quality Price Value This seems like manna from heaven for all the audiophile DIYers. Wish they had an office in India. (Posted on 3/5/10)
-
600W Class D Power Amplifier, Balanced Input, 2 Ohm Review by RICH
Quality Price Value I LIKE THIS AMP OVER THE TRIPATH 4 CHANNEL BOARD, IT IS SMOOTH ,SMALL BOARD. AND ONLY NEEDS ONE POWER SUPPLY VOLTAGE.. THE SPECS SHOULD TELL THE REST. THE POWER SUPPLY I AM USING HAS NEVER KICKED ON THE COOLING FAN, THIS SHOULD GIVE YOU AN IDEA OF HOW EFFICENT THAT THE BOARD IS. LOW POWER CONSUMPTION UNDER HIGH WATTAGE. I ALSO LIKE THE LOW IMPEDANCE [2 OHM] SO I CAN CONNECT MY 6 OHM KLIPSCH SPEAKERS IN PARALELL GIVING ME 4 SPEAKERS OUTPUT AT 3 OHMS EACH CHANNEL! (Posted on 11/20/09)
-
excelent Review by adrian
Quality Price Value super amplifier how can bay in romania? (Posted on 11/5/09)
